Chief architect x2

Please note that in order to install Chief Architect and the associated drivers and applications, you must have local administrative privileges on each computer. If you have questions about this, please stop now and consult with your network administrator. Install Chief Architect on the computer that will host the network hardware lock. This computer can be a server or other computer that can be accessed by all the workstations.

The hardware lock host machine must be using a version of Windows that meets your Chief Architect version's minimum system requirements. For more information, see the Related Articles section at the bottom of this article. The computer with the hardware lock should be in a secure location to help avoid the device being misplaced. Use a USB port in the back of the computer, not a front port or hub. It is important that you install the License Manager as a service rather than as an application.

To install the Chief Architect program Make sure that License Manager is running as a service on the computer hosting the hardware lock, and then begin by installing the program on the hardware lock host computer. After reading the disc, the Startup screen should display on the computer; but, if the Chief Architect installer does not launch: Double-click the file named Setup.

Install and register the software using the CD Key for the multiple-seat network license. This CD key will not work with the network lock as it is for the single-seat instructor license. If the program launches, you are ready to install it on the workstations. INI file, as described below. If you plan to image your workstations, make sure Chief Architect is functioning correctly on the original workstation before making your image.

This firewall prevents access to the computer with the network lock. To disable the Windows Firewall - Windows 7 or Vista Disabling the Windows Firewall is easier than configuring it, and is safe for computers that are already behind a hardware firewall. In the Tasks pane, select Windows Firewall. Otherwise, select Network Connections. On the Advanced tab, click the Settings button in the Windows Firewall section.

On the General tab, click the Off radio button and then click OK. Select Windows Firewall. Click on Advanced Settings, then click on Inbound Rules.

Click on New Rule, and then: Click Finish to save the new rule. To configure the Windows Firewall - Windows Vista If you do not want to disable the Windows Firewall, you will instead need to configure it to allow access across Port Click Network and Sharing Center. Click Change Settings. On the Exceptions tab, click Add Port.

Click OK to save this port. On the Exceptions tab, click the Add Port button. INI file In some situations, such as when machines are on different subnets or the hardware lock host computer has multiple network cards, you must tell Chief Architect the IP address or name of the host computer. To do this, use the NetHasp. For Chief Architect version 9. If the Installation window opens, close it.

Save a copy of the edited file in the Chief Architect installation folder. INI file. Additional Troubleshooting Steps If you are unable to launch Chief Architect after following the instructions above, here are some additional troubleshooting steps to try: Install Chief Architect on the server computer, if you have not already done so, and run the Hardware Lock Troubleshooter.

Note what hardware locks are installed and any error codes that appear on the first page of the troubleshooter. Verify that the correct lock is inserted on the host computer by starting Chief Architect and when prompted, launch the Hardware Lock Troubleshooter. The troubleshooter shows an entry for the network lock and the version of Chief Architect supported.

Make sure you can browse to the computer with the hardware lock through the Windows network. If this is not possible, contact your network administrator to determine why the network is not configured properly. Verify that you can see the hardware lock in the Windows Device Manager. If you opted to configure the Windows Firewall, temporarily disable the firewall to see if this makes a difference.

Check with your network administrator to see if any other firewall software is installed on the workstations or server. Check to see if there are any other network USB hardware lock devices on the local network. If so, remove them to determine if they are interfering. If you are having difficulty following these instructions, or do not have sufficient permissions on the network, please contact your network administrator for additional assistance.

If none of these steps resolves the problem, contact Chief Architect Technical Services either by telephone, or use the Online Support Center. Please be advised that there may be a fee for technical assistance with the discontinued versions of the software. Related Articles.

How to uninstall Chief Architect X2?

Jul 3, - Chief Architect X2 Full () | GB Chief Architect is specifically designed for the residential and light commercial design professional. Oct 26, - No specific info about version Please visit the main page of Chief Architect X2 on Software Informer. Editorial review: Read a full review. Chief Architect — professional 3D architectural home design software. Automated building tools make home design, remodeling, interior design, and kitchen.

chief architect x2

How much is a Capture One Pro software? | How much is it for Acrobat XI Standard Student and Teacher Edition for students?

TAGS:Standard 2019, Studio 2013, Ultimate OEM

В© Copyright 2019 jftpzq.me. All rights reserved.